Bondwater.com All Coupons
BOIL-OUT PROCEDURE STEAM BOILERS - Bond Water
BOIL-OUT PROCEDURE STEAM BOILERS PREFACE The internal surfaces of a newly installed boiler may be contaminated with oil, grease or other protective coatings used in the manufacturing process.
Actived: Saturday Dec 7, 2019
Boiler Water Treatment And Your Chemical Program
In addition, DEHA is volatile, so the excess over that needed for oxygen removal in the boiler carries off with the steam and is available to prevent oxygen corrosion in the condensate due to air in-leakage in condensate receivers and piping. When the steam leaves the boiler, the water treatment program’s job is still not done.
Boiler System - Tips on a chemical program for your boiler
Most boiler systems today burn natural gas as the primary fuel. Many systems are also set up to burn an alternate fuel if the natural gas supply is curtailed or cut off. In most cases, the alternate fuel is No. 2 fuel oil, a light distillate that is the same as diesel fuel.
Legionella Mitigation - Bond Water
Legionella Levels High Risk –Off Line Disinfection Part 2 Add fast-release, chlorine-containing disinfectant in pellet, granular, or liquid form, and follow safety instructions on the product label to achieve 50 ppm free chlorine. Record the type and quality of all chemicals used for disinfection, exact time
Cleaning HVAC Closed Loop Systems – What’s New? | Bond
Acid cleaning is too dangerous as there is often no way to off-vent gas developed during the process. In the past, high pH detergent cleaners were also utilized, but these can “shock the system” and break-off too much debris at one time which only serves to make matters worse. Bond offers a solution for recapturing lost system efficiency.
How to lay-up a cooling tower or cooling system for the
Protect Your Off-Line Cooling Systems This Winter Learn how to lay-up a cooling tower or cooling system for the winter? As we approach the cooler weather, it is not uncommon for some cooling systems to be shut down for winter and long term seasonal storage.
SAFETY DATA SHEET
Take off immediately all contaminated clothing. Take off immediately all contaminated clothing. Rinse skin with water/shower. Call a physician or poison control center immediately. Chemical burns must be treated by a physician. Wash contaminated clothing before reuse. Skin contact Immediately flush eyes with plenty of water for at least 15 minutes.
SAFETY DATA SHEET BELLACIDE 301 - Bond Water
SAFETY DATA SHEET BELLACIDE 301 1. IDENTIFICATION Product Name BELLACIDE 301 Chemical Name Contains tributyltetradecylphosphonium chloride. Product No. 101400, 101452 Identification No. 3082 Identified uses Biocides for water treatment. Keep run-off water out of sewers and water sources. Dike for water control.
Cooling Tower Cleaning Kits - Bond Water Technologies
With tower operating, close bleed valve cut off. Add 1/2 to 3/4 of the defoamer directly to the sump. Add the entire gallon of liquid cleaner directly to the sump. Circulate for 10-30 minutes. Add 5 pounds of the dry cleaner directly to the sump. Continue to circulate for 10-20 minutes.
BOIL-OUT PROCEDURE STEAM BOILERS - Bond Water
BOIL-OUT PROCEDURE STEAM BOILERS PREFACE The internal surfaces of a newly installed boiler may be contaminated with oil, grease or other protective coatings used in the manufacturing process. Such coatings must be removed since they reduce the heat transfer rate and could result in tube rupture from overheating.
Bond Algae Guards | Bond Water Technologies, Inc.
Contact Us Today and Get 10% Off! Algae Guard contains an EPA registered Micro-biocide and is a timed-release polymer strip blended with wetting agents and detergents. Engineered for all type units in 3 or 6 months sizes and packaged in blue kit enclosures. Features: 1) EPA Registered to control odors & biological growth in condensate pans
A Legal Perspective On Legionnaires’ disease - Bond Water
Overall, the hotel did not provide a safe environment for its guests due to the presence of Legionella in its water system. Hotels–especially those like the Defendant’s which are vacant during the off-season–often have problems with stagnant pipes which can lead to increased bacterial growth. This may have been an issue here.
Cooling Tower Cleaning Services | Bond Water Technologies
This can be accomplished by various methods, including the use of Bond online cleaning products to soften; clean dirt, calcium deposits, and other foulants; and pressure clean these deposits off the internal and external portions of your cooling tower.
SECTION 1: Identification of the substance/mixture and of
Plug the leak, cut off the supply. Dam up the solid spill. Knock down/dilute dust cloud with water spray. Take account of toxic/corrosive precipitation water. Powdered form: no compressed air for pumping over spills. Methods for cleaning up : Stop dust cloud by covering with sand/earth. Scoop solid spill into closing containers.
1. PRODUCT AND COMPANY IDENTIFICATION
P362+364 - Take off contaminated clothing and wash it before reuse. P273 - Avoid release to the environment. GHS Precaution Phrases: P303+361+353 - IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse skin with water/shower. P310 - Immediately call a POISON CENTER or doctor/physician.
PROPER BOILER LAY-UP PROCEDURES - Bond Water
boiler water before the boilers are taken off the line. No matter how mixing is accomplished, samples drawn from various sections of the boiler should be tested periodically to determine where or not the concentrations of alkalinity and sodium sulfite are satisfactory. If possible, deaerated water should be used to fill the boiler.
You’ve worked hard all spring, Water Treatment Program
You’ve worked hard all spring, summer and early fall keeping your cooling system free of scale, corrosion and microbi-ological growth and operating efficiently. You made sure in-hibitor levels were kept within recommended ranges and checked the bleed-off control-ler on a regular basis to assure that proper cycles of concen-
COOLING TOWER WET LAY-UP
1. Turn off the chemical or acid feed pumps. Also stop feeding any chlorine or bromine to the system. 2. Increase bleed-off in the cooling system until the conductivity of the cooling tower water matches the conductivity of the make-up water. If you are feeding chlorine or bromine, make sure free chlorine or bromine is equal to or less than
Coil Cleaning | Bond Water Technologies, Inc.
Therefore, any acidic or alkaline coil cleaner must be rinsed off of the coils as soon as possible to avoid pitting corrosion of coils. Coil cleaning can be a labor-intensive process. Our two proven solutions for coils makes it easy to clean coils, and extend the time between your scheduled cleanings.
Interactive Water Savings Calculator | Bond Water
Bond may be able to save you enough money through our Green Water Treatment Programs to pay for your entire water treatment program! Input your usage numbers into the easy-to-use interactive calculators on the left and see how we can save you thousands of dollars through water and energy conservation.
Safety Data Sheet BondPoly 2431-90S - Bond Water
Safety Data Sheet BondPoly 2431-90S Special hazards arising from the substance or mixture Hazards during fire-fighting: harmful vapors Evolution of fumes/fog. The substances/groups of substances mentioned can be released in case of fire. Spilled product is slippery underfoot. Very slippery when wet. Advice for fire-fighters
1. PRODUCT AND COMPANY IDENTIFICATION
P362+364 - Take off contaminated clothing and wash it before reuse. GHS Precaution Phrases: P301+330+331 - IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. P310 - Immediately call a POISON CENTER or doctor/physician. P305+351+338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Safety Data Sheet BondPoly 2431-90B
P362 + P364 Take off contaminated clothing and wash before reuse. Precautionary Statements (Disposal): P501 Dispose of contents/container to hazardous or special waste collection point. Hazards not otherwise classified If applicable information is provided in this section on other hazards which do not result in
Commercial Water Treatment Service Department | Bond Water
• Be willing to work off hours for equipment inspections or emergency situations • Maintain service vehicle, test equipment and inventories at company standards • Clearly communicate with field contacts via phone and email follow-up to validate service value. Are you interested in joining a winning service team?
MATERIAL SAFETY DATA SHEET - bondwater.com
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Shut off source of leak if safe to do so. Dike and contain product. Confine spill, soak up with clay, sand or other approved absorbent, shovel product into approved container for disposal. Wash area with plenty of water. SECTION 7 - HANDLING AND STORAGE
Material Safety Data Sheet - Bond Water Technologies, Inc.
Wash off immediately with soap and plenty of water removing all contaminated clothes and shoes. Inhalation . Move victim to fresh air. Call a physician or Poison Control Center immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Heat Exchanger | Bond Water Technologies, Inc.
THE COMMON PRACTICE of pulling the end bell heads off of chillers to inspect and clean the tubes of a chiller or condenser bundle has been utilized for as long as these pieces of equipment have been in use. With the increase of plate and frame heat exchangers being installed in HVAC applications, there has been a tendency to perform less preventive maintenance.
Cooling Water Treatment Services | Bond Water Technologies
Fully integrated control systems of the latest technology for on-site and off-site monitoring State-of-the-art closed system treatments, programs, and inhibitors, along with microbiological control Glycol system inhibitors and glycol monitoring
MATERIAL SAFETY DATA SHEET Bond 1570 Material
Material Identification and Use EFFECTIVE DATE.. 1/2/01 (Last revision N/A) White to off-white tablets with faint halogen odor. MATERIAL SAFETY DATA SHEET Bond 1570 Bond 1570 Page 2 of 4 Original Fire and Explosion Hazard Data MATERIAL SAFETY DATA SHEET Bond 1570 Bond 1570 Page 3 of 4 Original First Aid Measures
Contain run-off. UNUSUAL FIRE AND EXPLOSION DATA:.. None 6 – ACCIDENTAL RELEASE MEASURES LEAK AND SPILL PROCEDURES: .. Wear protective clothing, splashproof goggles and impervious overshoes. CAUTION: Keep spills out of municipal sewers and open bodies of water. Dike and
SureTemp™ Antifreeze Products
Toyota. Great for “topping-off” services. SureTemp™ Extended Life Heavy Duty Compatible with extended life Caterpillar/Texaco and GM DexCool®. For passenger cars and heavy-duty trucks. SureTemp™ Red Compatible with Toyota red extended life coolant. SureTemp™ Orange Compatible with GM DexCool. Passenger cars and light duty trucks.
BondClear 1330B SDS - Bond Water
For large amounts: Pump off product. Dispose of absorbed material in accordance with regulations. 7. Handling and Storage Precautions for safe handling No special measures necessary provided product is used correctly. Protection against fire and explosion: Take precautionary measures against static discharges.
MATERIAL SAFETY DATA SHEET BOND 8000 Material
Shut off source of leak only if safe to do so. Contain spill. Recover free product. To clean up residue, flush sparingly with water or use an absorbent. Avoid runoff to ground water, surface waters, and sewers. It may be necessary to remove contaminated soul. If product is flammable or combustible, use non
Career Opportunities | Bond Water Technologies, Inc.
BOND WATER TECHNOLOGIES IS ALWAYS PURSUING LEADERS from within the water treatment industry. If you are highly motivated, have set goals, and desire to achieve a higher level of job satisfaction and income, contact us for career sales opportunities. Contact Jim Clarke today Phone: 240.449.7208 Email: [email protected]
INSTANT - Bond Water Technologies, Inc.
using too much right off the bat. And freight costs? Why pay an extra $1 a gallon or more just to ship water? We thought you just might already have water where you are. With Instant Powder Packsstorage problems are gone. One package of 6 packs equals a gallon of 6 to 1 concentrate and weighs only one and a half pounds. It fits easily on a shelf,
MATERIAL SAFETY DATA SHEET - Bond Water
MATERIAL SAFETY DATA SHEET PRODUCT NAME: V - SHIELD Part B Page 4 of 4 SECTION 15 - REGULA TORY INFORMA TION TSCA (Toxic Substance Control Act) All components of this product are listed on the U.S. Toxic Substances Control Act Chemical Inventory (TSCA Inventory) or are exempted
Little Dipper & Bond's Cooling Water Dye Product Line
When coupled with one of Bond’s new cooling water Dye-trace inhibitor products such as our Bond 5009T and any bleed-off control unit with an appropriate 4-20mA input, your program application can be upgraded to the newest and most technologically advanced feed methods available.
MATERIAL SAFETY DATA SHEET
disclosed on an MSDS if found in a controlled product above the concentration cut-off. MATERIAL SAFETY DATA SHEET PRODUCT NAME: Part B PanShield Page 2 of 4 SECTION 4 - FIRST AID MEASURES INHALATION: Remove affected person to fresh air; wash mouth and nasal passages with water repeatedly; if breathing difficulties persist seek
MATERIAL SAFETY DATA SHEET Bond BIO-MAX
MATERIAL SAFETY DATA SHEET Bond BIO-MAX _____ www.bondwater.com Page 1 / 8 1. PRODUCT AND COMPANY IDENTIFICATION Product Name Bond BIO-MAX Contact Name Bond Water Technologies Skin Contact Wash off immediately with soap and plenty of water Inhalation Move to fresh air
BOND 15XT - Bond Water
BOND 15XT BOND 15XT PAGE 1 of 5 ORG Contain run-off. UNUSUAL FIRE AND EXPLOSION DATA:.. None. Safety Data Sheet BOND 15XT BOND 15XT PAGE 3 of 5 ORG 6 – ACCIDENTAL RELEASE MEASURES LEAK AND SPILL PROCEDURES: .. Wear protective clothing, splashproof goggles and